Whipping

Form a bight about 3" from the end of the whipping cord. Then, lay the running ends between the opposite strands of the rope. Make wraps moving clockwise, around the rope. Keep the wraps tight agains each other. Loop the bight over its strand and tighten it by pulling on the short end. Then finish by tying a square knot, pulling it tight between the strands of the rope.

Sailmaker’s Whipping

Scroll down for Sailmaker’s Whipping pictorial “How-to.”

The following text is by Adolph E. Peschke as presented in the 1998 printing of the 1993 edition of the Pioneering Merit Badge Pamphlet:

Whipping the ends of all the ropes in your pioneering kit is an indication of a well-managed kit, and a practice that will give your ropes good service in the field. Trying to tie knots in ropes with frayed ends is not only a bother but a waste of time. This can all be avoided by having a small spool of whipping cord as part of your pioneering equipment.

The type of whipping cord that you use is most important. Flax cord that is waxed and made of six strands is the best for pioneering work. Cotton string is not strong enough and will not wear well. Nylon cord is very strong, but tends to be slippery, especially when it’s waxed. A second drawback to nylon cord is that it stretches easily which makes it easy to slip off.

Waxed flax cord can be purchased at most leathercraft stores or shoe repair supply dealers.

The merit badge requirement for whipping can be fulfilled by using any whipping method shown in other Scouting publications. Because of the hard usage that ropes get during pioneering activities, it might be worth the time to learn how to do one or both of the following methods.

WEST COUNTRY WHIPPING

A group of countries west of Bristol, England, which has long been a seafaring area, is referred to as West Country. This area is also famous as a starting point for Pilgrims sailing to America. Why and how the West Country whipping was developed seems to be lost in history. Whoever invented it has left us with a simple and very effective method for whipping the end of a rope.

The West Country whipping works equally well on any type of rope, twisted or braided, or rope made from natural fibers or plastic filament. (All plastic ropes should have the end melted back first.) The success of the whipping depends on the tightness of the knots formed by the cord and the interlocking action of the Overhand Knots.

To make a West Country whipping on a 1/4″-diameter rope, start with a 14″ length of waxed flax cord. Wrap the cord around the end of the rope about 1/2″ to 3/4″ from the end, and tie an Overhand Knot (see photo 1). If the rope is badly frayed, it can be pulled together with a clove hitch or Constrictor Knot to begin the whipping.

Photo 1: Use waxed flax cord and tie an overhand knot about 3/4" from the end of the rope.  Photo 2: Wrap the whipping cord around the back of the rope and tie another overhand knot  Photo 3: Repeat tying overhand knots, front and back, until the whipping is 1/4" to 3/8" long. The tie a square knot to finish the whipping

West Country Whipping

Continue by taking the two ends of the whipping cord around the the back of the rope (away from you), and tie another Overhand Knot (see photo 2). Keep repeating Overhand Knots, front and back until the whipping has been formed. A good rule of thumb to follow when making this kind of whipping is to make the whipping as long as the diameter of the rope.

Always tie each Overhand Knot right over left of left over right so that the knots lay neatly together and snug against the previous knot to form a smooth finished whipping. The West Country whipping is finished with a Square Knot and the excess cord is trimmed.

SAILMAKER’S WHIPPING

Just the thought of sails and ropes flapping in a strong wind when a sailing ship is under way makes you realize that the ends of the ropes aboard a ship have to be whipped to keep them from raveling under the strain. Sailmakers knew that a little extra effort spent whipping the ends of the ropes would make their work much easier in the long haul.

To make the sailmaker’s whipping, first unlay the three strands at the end of the rope about 1″ (see figure 81). With a length of whipping cord approximately 16″ long, form an open bight about 3″ long at the end of the cord. Slip the bight over one strand and then lay the two running ends of the cord between the remaining two strands of the rope. (See A and B in figure 81).

Relay the strands of the rope to form the original twist (see figure 82). Then wrap the long end of the whipping cord tightly around the rope. Wrap the cord clockwise, moving toward the end of the rope approximately six turns. Keep each wrap tight against the previous one and neatly together (see figure 82).

Figures 81, 82, and 83

Figures 81, 82, and 83

To complete the whipping, bring the original bight up over the same strand it was originally looped over (see figures 81 and 83). Then pull the short end of the whipping cord until the bight is pulled tight on top of the wrappings. Finally, bring both ends of the whipping cord, (A) and (B), up to the end of the rope and tie a Square Knot, pulling it down tight between the strands of the rope and snug on top of the wraps (see figure 83). Cut off any excess from the ends of the whipping cord. This sailmakers whipping will stay put under hard use.

Get ready to begin. Unlay the three strands about an inch or so. Feel free to mark strand 1. Spread out the strands for  easy access. Make a bight in the whipping cord and slip the loop over strand 1, between strands 2 & 3. Relay the three strands. Holding the bight and the rope in one hand, take the long end of the cord in the other hand. Begin to wrap the long end of  whipping cord around the rope. Continue wrapping tightly. Done wrapping. Unlay the three strands Take hold of the loop and slip it over strand 1. With the short end of the whipping cord, pull the loop tight over strand 1. With the short end of the whipping cord, pull the loop tight over strand 1. Place the long end of the  whipping cord between  strands 1 & 3. Join the short and long ends of the whipping cord with a square (reef) knot. Pull it tight. Twist the top strands of the rope back together. Trim the excess off the top.

How to Tie a Sailmaker’s Whipping (Click on the image once and then again to bring up the largest view.)

Alternate Procedure for Beginning the Whipping

Categories: Scout Pioneering | Tags: , , , , , , , , , | 8 Comments

Post navigation

8 thoughts on “Whipping

  1. Pingback: Knot-Tying Terminology | SCOUT - PIONEERING

  2. Pingback: Jamboree Pioneering Area: Camp Gadgets, Rope Making & Instruction | SCOUT - PIONEERING

  3. Pingback: Foolproof Way to ALWAYS Tie a Square Knot Right | SCOUT - PIONEERING

  4. Pingback: The Older Pioneering Merit Badge Pamphlet | SCOUT - PIONEERING

  5. Pingback: The Older Pioneering Merit Badge Pamphlet | SCOUT - PIONEERING

  6. Pingback: Introduction to Pioneering | SCOUT - PIONEERING

  7. Pingback: Lashing INFORMATION | SCOUT - PIONEERING

  8. Pingback: Get Pure Manila Rope and Don’t Be Fooled! | SCOUT - PIONEERING

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Blog at WordPress.com. The Adventure Journal Theme.

Follow

Get every new post delivered to your Inbox.

Join 55 other followers

%d bloggers like this: