Tag Archives: Swing Boat

12-foot Swing Boat

A Swing Boat is a fairground ride in which pairs of riders pull ropes to swing back and forth. At the national jamboree, it’s one of the pioneering area’s favorite features. Click here for more information. This is a smaller, more boy-sized version, but still lots of fun and plenty big enough.

ALL LASHINGS MUST BE VERY TIGHT! (This is an appropriate occasion to start the Japanese Mark II Square Lashing with a clove hitch in the middle of the rope around the upright, under the crossing spar, before proceeding with the wraps.)

After completed, the A-frames are stood up and held in place while other construction continues.
After completed, the A-frames are stood up and held in place while other construction continues.

Build the A-frames. Using 20-foot ropes, lash two identical A-frames. The tops of the shear lashings needs to be approximately 3 feet below the tips of the 12-foot legs. (In lieu of shear lashings you might want to join the legs at the top with looser square lashings applied with the legs held at 90º after which the legs can be brought into the desired position to add the ledgers, but in doing so, make sure there won’t be too much strain applied to the top rope and the spars.) The 10-foot ledgers need to be approximately 1.5 feet above the butts of the legs. Lash on an additional 6-foot cross spar for extra support on each A-frame.

Join the A-frames together. Stand up the A-frames and holding them in place, use the remaining 12-foot spars to join them together. Lash these on as low as possible so they don’t interfere with the action of the swing.

The following steps can be carried out using an 8 to 10-foot folding step ladder or by laying the structure on its side. Either way, strong crew members will be needed to hold the spars in place. 

Add the Center Spar. With a TIGHT square lashing, lash the stout 10-foot center spar to the inside of one leg of each A-frame, about 1 foot from each end where the tops intersect. This will provide a good, inward lean to the A-frames. (If you are using rope grommets with steel rings, attach them to the center spar with a prusik, about 6 inches from the legs of each A-frame.)

Tightening a Square Lashing on One of the Parallel Top Support Spars
Tightening a Square Lashing on One of the Parallel Top Support Spars

Lash on the top support spars. Join the tops of the A frames by tightly lashing a 10-foot spar on the legs of each A-frame, about 6 inches from the tips. (It’s a good idea to start these lashings with a constrictor knot to minimize slippage during use.)

Attach the pull rope spar and pull ropes. At right angles, lash a 10-foot spar across the center for the pull ropes. About 6 inches from the ends, tightly tie a 15-foot pull rope to each end using a roundturn with two half hitches.

Attach the swing. Attach a swing rope to each end of the prepared plank with a scaffold hitch. Using a roundturn with two half hitches, tie the ends of each swing rope securely to their corresponding ring -or- directly to the center spar about 6 inches from the legs of each A-frame.

Add the guylines. Using a roundturn with two half hitches or rolling hitch, attach a 36-foot x 3/8-inch guyline to the top of each leg. (If, the structure has been on its side, it’s time to stand it completely up.)

Anchoring the Ledger with Pioneering Stakes
Anchoring the Ledgers with Pioneering Stakes

Prepare the anchors. Drive in pioneering stakes for four 1-1 anchors extending 20 feet out from the legs at 45º. Attach the corresponding guyline to each using a rope tackle. Also, drive in a stake about 6 inches in at each of the four corners so they will intersect with the A-frame ledgers. Lash each stake to the corresponding ledger with a square lashing.

Make adjustments. Level out the plank to the desired height and adjust the swing ropes so the swing hangs evenly.

Materials

  • 6     12-foot  x 4-inch spars
  • 6     10-foot x 4-inch spars
  • 2     6-foot x 3-inch spars
  • 18   20-foot x 1/4-inch lashing ropes
  • 2     36-foot x 1/2-inch swing ropes
  • 4     36-foot x 3/8-inch guylines
  • 12   pioneering stakes
  • 4     tent stakes and lengths of rope or binder twine for 1-1 anchors
  • 1     2-inch x 8-foot board (sanded and notched about 6 inches from the ends)
  • 2    rope grommets with steel rings (optional)

Pioneering at the 2014 Dixie Fellowship

Santee Lodge 116, Order of the Arrow hosted this year’s Dixie Fellowship at Camp Coker. With the input of the Dixie Design Team comprised of Pioneering Crews from Chicora, Iswa and Attakwa Chapters, Arrowmen erected a 24 foot six flag, banner gateway flying the American flag, the Order of the Arrow flag, the World Scout Crest flag, and the state flags of NC, SC, and GA. These six flags surrounded a 10’ banner welcoming everyone to the Dixie Fellowship! The OA Pioneering Crews also built a 12’ Swing Boat and 10’ Atomic Pile for intermittent fun during the Fellowship.

Building and Hoisting the Gateway / Flags Flying / Gateway During the Day and Illuminated at Night / Tomo Chi Chi Lodge Photo
Building and Hoisting the Gateway / Flags Flying / Gateway During the Day and Illuminated at Night / A Group Shot of Some Arrowmen from Tomo Chi Chi Lodge Under the Banner
The Swing Boat was situated near the Trading Post.
The Swing Boat was situated near the Trading Post.
The Atomic Pile challenged Scouts behind the Trading Post.
The Atomic Pile challenged Scouts behind the Trading Post.