A crew of Scouts went about erecting a FLOATING FLAGPOLE made entirely of Scout staves. They lashed together five staves for the pole and two staves each for the three supporting uprights. The idea was to rely upon the strain of the guylines to keep the uprights straight, without sinking them into the ground. The problem was the two staves making up each upright were just too rickety to effectively withstand the stress created during the hoisting process.
All in all, it worked, but attention should be directed to the lashings joining the stoves for the uprights. —> Use longer lashing ropes or apply three round lashings, and, make sure they’re really tight!
A flagpole suspended off the ground by a series of lines, so that it appears to be floating, can be a really neat project. The structural principle has been referred to as tensegrity, and is based on using one half the lines to lift the pole off the ground, and the other half to give it stability, supporting it in a vertical position. On occasion, Scouts choose to use more than three upright support poles, but just like with a simple flagpole employing three supporting guylines, three upright poles provide the required balance needed to hold the pole up straight. The longer the support poles, the higher off the ground the flagpole can go.
There are many ways Scouts go about constructing a suspended flagpole. The following materials were used for this particular flag display:
one 20-foot bamboo pole (flagpole)
three 10-foot x 3-inch pine spars (upright support poles)
nine pieces of rebar, sawed to 3 feet each
six 50-foot lengths of 3/8-inch manila (guylines)
three 3/8-inch double pulley blocks
50-foot length of 1/4-inch braided nylon (for the halyard) along with a couple of clips
six pioneering stakes
wooden mallet (for driving in the stakes)
club hammer (for driving in the rebar)
roll of friction tape
lengths of 1/4-inch braided nylon cord
The following initial steps were taken for this particular flag display:
Where the flagpole will be placed, 9 feet from the center of an equilateral triangle, three holes are made, 4 inches in diameter and 2 feet deep.
A double pulley is securely tied to the top of each 10-foot support pole and a 50-foot guyline is reeved through each sheave.
A 10-foot upright support pole is planted in each hole which is packed with excavated material. Three lengths of rebar are pounded in around each spar.
A span of friction tape is applied to the areas of the 20-foot flagpole, where the lines will be tied (bamboo is slick)
The metal ring is tied to the tip of the 20-foot pole and the halyard is threaded through.
A 1-1 anchor is installed about 9 feet behind each 10-foot spar
The following rigging procedure was followed for this particular flag display:
The guylines from each upright support pole are tied to corresponding loops in the jury mast knots at the top and bottom of the flagpole with two half hitches, the tail of which is tightly seized to the standing part using binder twine with a West Country Round Lashing.
The following procedure was followed to raise and supportthis particular flag display:
When the flagpole is rigged and everything is in place, two or more Scouts lift up the pole in the center of the triangle, and hold it erect.
One Scout mans each lifting guyline tied to the bottom of the pole. On signal, they all pull these lifting lines until the strain assumed by the Scouts holding the pole erect is replaced by the lower, lifting guylines. (Note: If the pole is taller or heavier, an additional Scout needs to man each guyline attached to the top, in order to stabilize the pole as it’s being held up, keeping it from tilting or falling. However, tension is only applied to offset any overt tilting.)
When the lifting guylines have taken up the strain to hold the flagpole at the desired height (about half the length of the upright support poles protruding from their holes), a butterfly knot is applied at the appropriate place and they are secured to the 1-1 anchor with a rope tackle.
When the lower guylines are well secured, the upper, stabilizing guylines can be adjusted so that the flagpole is held up in a straight position. When the flagpole is even, the upper lines in turn are secured to their respective anchors with a rope tackle.
—> An alternate approach can be taken in which the flagpole is first stabilized in an upright position by the three upper guylines. These can then be temporarily secured, readying the flagpole to be raised off the ground. Once standing in a vertical position, upward force is applied to the flagpole by a Scout or Scouts holding on to the bottom and lifting, in conjunction with a simultaneous pulling on the bottom lines and a simultaneous easing off on the top lines. This lifting process is illustrated HERE.
GOOD, OL' FASHIONED, OUTDOOR, SCOUTING FUN FOR THE 21ST CENTURY!