Simple Rope Halyard

In the campsite it’s easy to fly the colors by simply tying them directly to the top of the simple flagpole with a couple of short cords. But, on a taller pole that’s going to stay standing, and when you want to raise and lower the flag(s), of course you need a halyard. Here’s one ultra simple recipe that will work with ease and that you can use with confidence:


  • A length of 1/4-inch nylon cord that is almost twice as long as the flagpole is high. If your flagpole will be thirty-two feet high, sixty feet of cord will work well.
  • 1/4-inch pulley
  • 2 small carabiners for each flag
When joining the ends of  smooth, slippery rope, the water knot won't fail.
When joining the ends of smooth, slippery rope, the Water Knot won’t fail.


• Fuse the ends of the nylon cord.

• String on the pulley and join the ends of the nylon cord with a water knot.

The Top of the Halyard
The Top of the Halyard

• With an indelible marking pen, mark the middle of the cord. This middle mark will be be just about at the top of the flag pole.

• Stretch out the cord and lay out the flag(s) the desired distance from the middle mark, and using small butterfly knots, tie a fixed loop at each grommet.

• Attach a carabiner to each loop.

Top of the Rope Halyard with the carabiners attached in position.
Top Section of the Rope Halyard with the Carabiners Attached to Match the Positions of the Grommets

When you’re ready to use the halyard, attach the pulley to the flagpole at the top with a prusik or a rolling hitch on a doubled rope. For shorter, lighter flagpoles, in lieu of a bully, the halyard can be reeved through a simple metal ring.

The MOST Simple Halyard

Easy Tall Flagpole

At most Scouting events, there isn’t a permanently-installed, tall, metal pole for raising and lowering the colors. During opening ceremonies at these Scout gatherings, a tall flagpole made by joining long spars together can impress and inspire.

Opening Ceremony at a District Camporee
Opening Ceremony at a District Camporee

What is meant by tall? Naturally, the height of the flagpole depends on the size of the flag and the size of the area where it will be raised. For the most part, the flags used in Scouting are 3 x 5 feet, and the average size outdoor flagpole for a 3 x 5-foot flag is 20 feet. Of course, the main criteria for flagpole height is how far away you want the flag to be seen. But also, flying a flag high is synonymous with pride, and the taller the pole the greater the impact. However, this post is about a simple flagpole and not a pioneering display of goliath proportions. The specific flagpole featured on this page topped out at 32 feet, which was impressive, but not uncanny.

Building and putting up a taller flagpole requires more attention than one for an easy campsite setup, but all in all it’s still a relatively simple operation. Basically, four things are needed:

  1. Long spars
  2. An effective way to join the spars together so the flagpole will be rigid
  3. A series of planned steps to take before standing the flagpole up *
  4. A crew to lift the flagpole to its vertical position

Long spars. Depending on your point of reference, the definition of long spars is relative, and will hinge on what’s available in your geographic area and how practical it is to procure and transport them. Naturally, the longer the spars the fewer you’ll need to make the pole tall, which of course has obvious advantages. Again, depending on your point of reference, a long spar can be seen as having a length anywhere from 10 to 20 feet.

Tall View
Simple, Tall, Pioneering Flagpole

In the flagpole featured on this page, there are three long spars: 16-foot bottom, 14-foot middle, and 10-foot top. The lower the spar, the larger the diameter. The butt end of the next spar up should be as near to the same diameter as possible to the top of the one it’s joining.

West Country Round Lashing Joining Two Bamboo Spars

An effective way to join the spars together so the flagpole will be rigid. Obviously, the rigidity of the flagpole is a primary concern. You don’t want it to bend and  you don’t want it to come apart. It has to ever-withstand the stress of its own weight in a vertical position, as well as the weakening forces of wind, rain, and varying temperatures. When it comes to joining spars together to extend their length, there are basically four lashings that can be employed. For the tightest and most secure lashing, the West Country Round Lashing works really very well.

When the utmost rigidity is required, a quarter of the spars’ lengths should overlap each other. Using long lengths of 1/4-inch manila rope, start each of the two lashings approximately 1-1/2 to 2 inches from the ends of the overlapping spars and tie at least ten tight half knots (overhand knots) towards the middle of the overlap. Depending on the length of the lashing rope and the size of the spars, for added security, additional lashings can be tied e.g. in the photo to the left, where the bottom spar and the middle spar overlap, four West Country Round Lashings were applied.

* A series of planned steps to take before standing the flagpole up. Before transforming the finished flagpole from horizontal to vertical, these steps need to be taken:

  1. Determine the spot on the ground where the flagpole will stand and dig a hole about 4 inches deep with a diameter just a little larger than that of the flagpole’s butt end.
  2. Position the flagpole so the bottom is right over the hole.
  3. To attach the rope halyard, tie a small rope grommet and pulley to the top of the flagpole with a prusik.
  4. Reave the prepared rope halyard through the tackle.
  5. Attach four guylines of the  proper length (see: Guylines.) Tie the guylines to the flagpole about 3/4 up the pole with four rolling hitches. Tie them on so they will each line out to their respective anchors.
  6. Measure out the proper distance from the bottom of the flagpole in four perpendicular directions and mark the spots where the front pioneering stake will be driven into the ground for each 1-1 anchor. The rule of thumb is drive in the stakes at a distance equal to twice the height from where the knots were tied, measured out from the base of the flagpole.

  7. Build four 1-1 anchors in readiness for attaching the four guylines.

A crew to lift the flagpole to its vertical position. When ready, four crew members each take hold of a guyline and position themselves in line with their respective anchors. Additional crew members line up along the length of the flagpole ready to walk the pole up to its vertical position. One member is stationed at the bottom to guide the pole into the hole as the others lift. When everyone is in position, a signal caller gives the go ahead to lift. Those with the guylines pass the ends of their lines behind the front stake of their anchor. Once the flagpole is standing upright, each guyline is secured to its anchor with a rope tackle. Final adjustments can then be made to each guyline until the pole is standing straight.


Favorite Pioneering Knots: Prusik

Link to: Older Pamphlet Info

A Prusik is tied by first making a rope grommet (fixed loop).After attaching the grommet around the spar forming a common lark’s head. Next, inside the middle of the lark’s head, wrap the loop around the spar at least two complete times. When finished, position the Prusikand pull the loop tight
Attaching a light pulley for a rope halyard on a flagpole.

The following text is by Adolph E. Peschke as presented in the 1998 printing of the 1993 edition of the Pioneering Merit Badge Pamphlet:


This knot has the reputation of having a firm, sure grip once it is put under pressure. The multiple opposing turns provide friction and put a bend in the standing part of the rope, which becomes more difficult to pass through the turns as a lateral pull is applied. The prusik is widely used by mountain climbers as they attach a loop (grommet) made from a smaller rope to a larger rope to form a hand or foothold. It can also be used to form hand and shoulder loops for a lateral pull on another rope or to drag a log or spar. Pioneering Uses

  • To hook a light tackle on a vertical or horizontal spar.
  • To make hand and foot loops for climbing another rope or vertical spar.
  • To make hand and shoulder loops as an aid to hauling a large log. It can easily be moved along as the positions require.
  • To provide the grip and a loop to tie another line with a sheet bend.
  • To provide a safety brake against back-slipping on a load-lifting line. (Do not use when lifting a person.)
Prusik Tying Sequence
Prusik Tying Sequence